USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!


Public Profile
7daniel49
Customer Type: Platinum Member
Location: anchorage, UNITED STATES MINOR OUTLYING ISLANDS
My movies
Recent product discussions
Versus Composite DLG 1500mm Glider (ARF)
2.4 compatible? ...
FatShark Dominator 3rd Generation modular FPV System
So these do not come with a receiver? What is the difference between these goggles and the predators...
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)
Oh no! Not another question about the turnigy 9x! Guys, I'm flying a two channel (elevon) sal glid...
Turnigy Ultra-light wood propeller 10x6
Hey, guys. I run a 10x4.7 gws prop on my tricopter with the dt750's. What would be a good, less flim...
H550 V1 Glass Fiber Hexcopter Frame 550mm
Do you guys think it would be possible to take out half of the arms and make a tri?...
HobbyKing Cell Key - 6s Lipoly Cell checker
Will this work on a 1 cell lipo? Does anything?...
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)
I need the smallest/lightest receiver that will work with this transmitter. Will any of the 3ch hobb...
Turnigy balancer & Charger 2S-3S
Alright guys, I'm in need of some help. http://www.hobbyking.com/hobbyking/store/images/em_bigsmile....
HobbyKing Multi-Rotor Control Board V3.0 (Atmega328 PA)
I can't seem to reverse the gyro compensation for the yaw. I have tried the regular procedure, but i...
GWS EP Propeller (RD-1047 254x119mm) (6pcs/set)
Does anyone have a buddy code for these? I have been waiting forever, and my buddy code expired... T...
Recent discussion reply
Turnigy TrackStar ESC Programing Card
I second that it will NOT work with the 120A trackstar. I dont know why, but it doesn't. ...
hexTronik DT750 Brushless Outrunner 750kv
Use these with 3s. They are very efficient, a bit more efficient than the ntm from my experience. If...
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board
You need to have one esc from m2-m4 connected to the board all the way. Something about the lcd take...
hexTronik DT750 Brushless Outrunner 750kv
Use 4mm piano wire for the shafts. The bearings are 4x8x3. I got mine at fasteddybearings online for...
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board
Press Button 4, 3x4 (button 3, four times), 4, 3, 4, 1, 3x30 (a lot ), 4 If this helped you out, pl...
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)
Yes it is! There are even modes 3 and 4, but you have to take the back off of the transmitter and ta...
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board
Should be down right or down left on the rudder/throttle stick. If this doesn't work, the make s...
hexTronik DT750 Brushless Outrunner 750kv
Yes, it helps to have a nut on the top and bottom so you don't pull the shaft end against the be...
NX-4005-650kv Brushless Quadcopter Motor
These motors are far more efficient that the dt750's in real world circumstances. I saw a guy on...
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board
Why spend $15.00 plus shipping to protect a $30.00 board? Why not make something, or take your chanc...
Wiki-blog entries.

Share