Please confirm your location:




Public Profile
Johnsn
Customer Type: Platinum Member
Location: Kailua-Kona, UNITED STATES
My movies
Recent product discussions
Walkera Super CP Flybarless Micro 3D Helicopter w/Devo 7E - Mode 2 (RTF)
Hi, is there also the simulator cable included? Which one is better, this or the FBL100 ?...
TURNIGY Plush 6A /.8bec/6g Speed Controller
Can this be flashed with SimonK firmware? Has it the Atmega chip or the Silabs?...
5030 Propellers (Black) - 3xCW and 3xCCW - 6pcs per bag
Should I buy this props or are the 3-blade of the shop better for a micro quad?...
Glass Fiber Cloth 450x1000mm 18g/m2 (Super Thin)
When it will arrive in Stock?...
Hobbyking OSD System (Full Combo): Main Board, Power Module, USB/GPS/IR/TEMP Modules w/Remote
Hi, what are the minimum and maximum data of altitude (up to 40km?), distance (100km?), speed(1000km...
Hobbyking OSD System (Full Combo): Main Board, Power Module, USB/GPS/IR/TEMP Modules w/Remote
Hi, what are the minimum and maximum data of altitude (up to 40km?), distance (100km?), speed(1000k...
FrSky V8R4-II 2.4Ghz 4CH Receiver
has this receiver a ppm out?...
HXT 9610 Low Profile Metal Gear Servo 33g / 7.4kg / .16sec
how much amps does it pull?...
HobbyKing® ™ Brushless Car ESC 30A w/ Reverse
Why are there 7wires?? can i use this esc with this motor?: http://www.hobbyking.com/hobbyking/stor...
hexTronik 20gram Brushless Outrunner 2300kv
will this work with a gws 3blade 5030 on 3cell?...
Recent discussion reply
TURNIGY Plush 25amp Speed Controller
Of course! You can connect every 2 to 4 cell LiPo battery to it, regardless of the amount of mah. If...
ZIPPY Flightmax 1800mAh 9.9V 5C LiFePo4 TX Pack
Yes, it fits in....
hexTronik DT750 Brushless Outrunner 750kv
The danger is that it goes off and hits you. If it doesn't hit you (if it's up in the air), your tri...
hexTronik DT750 Brushless Outrunner 750kv
You can mount the prop with zip-tie, but you will get a little more vibrations because it's not comp...
ZIPPY Flightmax 8000mAh 4S1P 30C
Bei mir waren AWG10 drauf, passen gut in die EC5 Stecker von HK!...
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)
Take this one from Hobbyking, it works great with the er9x software: http://www.hobbyking.com/hobbyk...
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)
I think 60mw, never had a single glitch or loose of control with the radio....
ZIPPY Flightmax 1800mAh 9.9V 5C LiFePo4 TX Pack
I set my alarm to 9.1 volt first and changed it to 9.0 volt, but never reached that less battery pow...
TURNIGY Voltage Booster for Servo & Rx (1S to 5v 1A)
yes and they worke great. have two of them, both work great and are powering the servos in my model....
TURNIGY Voltage Booster for Servo & Rx (1S to 5v 1A)
yes look at google for "anyvolt" and similar products....
Wiki-blog entries.

Share