Please confirm your location:




Public Profile
Nobby
Customer Type: Platinum Member
Location: Forestville, AUSTRALIA
My movies
 
Recent product discussions
ActionCam Inline Gimbal for FPV and Multi-Rotor (AU Warehouse)
Can somebody please tell me the size between the arms of the camera support as it could be either 91...
EP 450 Class 320mm Carbon Fiber Main Blades for 4-Blade Main Rotor (2pc)
I wish that they didn't put the kicker on the tip as it makes the transsional lift to strong at a p...
OrangeRx Open LRS 433MHz TX Module (JR/Turnigy compatible) (AU Warehouse)
How come the Picture is of a RX module or at least thats what it looks like to me? and can that type...
Minim OSD v1.1
Just a quick Heads up,The regulator is too weak for being hooked up with a 12v power source,5v no pr...
Hobbyking YEP 60A (2~6S) SBEC Brushless Speed Controller ( (AU Warehouse)
From what I can tell from Mine,the default mode is Heli,Soft start = medium maybe as it spins up qui...
Hobbyking YEP 60A (2~6S) SBEC Brushless Speed Controller ( (AU Warehouse)
Just uploaded the PDF manual for this controller should be clear soon. If you want to program the Es...
Hobbyking YEP ESC Programming Card
I'm told that the V2 card they have now will work with the 60 amp YEP esc Has anyone used this card ...
HobbyKing 450 Helicopter 5-Blade Flybarless Rotor Head
Please TRY the Plastic Blades that HK sell for these heads 4 and 5 bladers theyre great ! roots are ...
Assault 700 DFC - Metal Tail Assembly Complete
Are all the alloy parts CNC milled ,which Parts are Cast (like the main shaft bearing holders!) Not ...
HobbyKing 450 4-Blade Rotor Head
Does anyone know if the blade holder pin should go forward of the rotation or at the rear. Mines ass...
Recent discussion reply
Openpilot CC3D Flight Controller With Cable Set Fully Authorized
yes this board can work incredibly well in a wing or a fpv plane or a car /Tank /Boat anything you w...
Turnigy Micro-X Quad-Copter DSM2 Compatible with FTDI Tool MWC (Multi-WII) (BNF)
Check where the wires from that motor run back to the PCB as there must be a slight short in the mot...
Turnigy Micro-X Quad-Copter DSM2 Compatible with FTDI Tool MWC (Multi-WII) (BNF) (AU Warehouse)
Yes you can run the MultiWii settings software using the usb FTDI provided.So then you have access t...
Turnigy Micro-X Quad-Copter DSM2 Compatible with FTDI Tool MWC (Multi-WII) (BNF) (AU Warehouse)
But where do you find a harness for the Donkeys on the HK site?????? *-)...
Turnigy Micro-X Quad-Copter DSM2 Compatible with FTDI Tool MWC (Multi-WII) (BNF)
their are brushless motors which have built in esc's but I dont know if they go that small,their was...
Turnigy Micro-X Quad-Copter DSM2 Compatible with FTDI Tool MWC (Multi-WII) (BNF)
Go for the Orange dsm2 and for the money theyre great!...
Circular Polarized 5.8ghz Antenna Set (SMA) (LHCP) (60mm)
Yes Dan I would advise you do as the RG62 coax dos not have the ability to hold a bend,and I would a...
Heavy Duty Pan and Tilt Base Kit with 160deg Servos Robotic Limb or Antenna Tracking (Short Arm)
http://www.hobbyking.com/hobbyking/store/__40641__General_Use_FPV_and_Camera_2_Axis_Servo_Gimbal.htm...
Heavy Duty Pan and Tilt Base Kit with 160deg Servos Robotic Limb or Antenna Tracking (Short Arm)
I would go for this 2 axis for a couple of bucks more Its a better design gimble I believe. http://w...
Minim OSD v1.1
That's good to know EricBR as this means the reg is more than adequate to the task,which means I wil...
Wiki-blog entries.

Share