HobbyKing Forums
Forum Home Forum Home > Product Specific > Motors > ESCs
  New Posts New Posts RSS Feed: Turnigy "SuperBrain" ESC
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Turnigy "SuperBrain" ESC

 Post Reply Post Reply Page  <1 13141516>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
flarssen View Drop Down
Platinum  (NO)
USERID: 3342
Hobbyking Addict
Hobbyking Addict


Joined: 15/May/2009
Online Status: Offline
Posts: 1225
  Quote flarssen Quote  Post ReplyReply Direct Link To This Post Posted: 11/Apr/2012 at 12:18am
Thanks for sharing, Ron.
I bought one myself last December, and haven't used it yet either.
Please share your experience here when you have tried it.
I tried one of the smaller ones (20A) in a 450 heli, but it always shut down after a few seconds on a kv4000 motor, even unloaded. It worked fine on a lower Kv motor, but I never tried it in the air.

Fred

Edited by flarssen - 11/Apr/2012 at 12:28am
Back to Top
JoshyJS View Drop Down
Platinum  (DE)
USERID: 263106
Newbie
Newbie


Joined: 18/Jul/2009
Location: Germany
Online Status: Offline
Posts: 14
  Quote JoshyJS Quote  Post ReplyReply Direct Link To This Post Posted: 29/Jun/2012 at 5:33pm
Hi there,

I have a Super Brain 60A in my Angel S30E.
Aeolian 4250 600KV.
Prop APC E 13x8
2650 40C 2x2S Zippy in row for 4S.

According eCalc there shoud be max 35A current.
According logging I have more than 56A.

During flight with full throttle sunddenly it switches the engine off.
Throttle back to idle and pushing up restarts the engine immediately.

Any idea what to change or what do I do wrong?



Edited by JoshyJS - 29/Jun/2012 at 5:36pm
Back to Top
2Doggs View Drop Down
Platinum  (US)
USERID: 361228
HobbyKing aficionado
HobbyKing aficionado


Joined: 06/Dec/2010
Online Status: Offline
Posts: 203
  Quote 2Doggs Quote  Post ReplyReply Direct Link To This Post Posted: 29/Jun/2012 at 7:50pm
Hi JoshyJS, the problem you describe sounds like RF interference - the SB will shut off power to the motor if it loses signal, and when signal is restored, power can be enabled by bringing the stick all the way down.

I used to get some interference when I was running on 35mHz, but since using an FrSky 2.4G module and RX in my JR radio, it's been fine. You could try using a ring on the ESC RX lead, with about five turns, otherwise maybe try a separate UBEC. You may also be able to move your RX further away from the ESC.

Good luck!
Back to Top
JoshyJS View Drop Down
Platinum  (DE)
USERID: 263106
Newbie
Newbie


Joined: 18/Jul/2009
Location: Germany
Online Status: Offline
Posts: 14
  Quote JoshyJS Quote  Post ReplyReply Direct Link To This Post Posted: 30/Jun/2012 at 12:59pm
Huhu.

The ESC sits completely alone about 10cm away from the receiver.
ESC in front of the fuselage, receiver far in the back.

In the meantime i figured out:
When I set the ESC to Soft Cutoff it does not cut the engine, it regulates down.

Here are some loggings:

With Hard cutoff:



An with soft cutoff:



But the cutoff should start at 12V. But it starts at 13,2V. Far to early.
Back to Top
2Doggs View Drop Down
Platinum  (US)
USERID: 361228
HobbyKing aficionado
HobbyKing aficionado


Joined: 06/Dec/2010
Online Status: Offline
Posts: 203
  Quote 2Doggs Quote  Post ReplyReply Direct Link To This Post Posted: 30/Jun/2012 at 10:43pm
Yes, I think you're right. What settings have you got for LVC? The default is "Standard", which is appropriate for 2S packs, but you should set it to "disabled" for 4s.

Back to Top
JoshyJS View Drop Down
Platinum  (DE)
USERID: 263106
Newbie
Newbie


Joined: 18/Jul/2009
Location: Germany
Online Status: Offline
Posts: 14
  Quote JoshyJS Quote  Post ReplyReply Direct Link To This Post Posted: 01/Jul/2012 at 2:29pm
Its not possible to set LVC to disabled.
Only 3/6/9/12..... V oder to an Accu standard.

I have it on 12V.
Back to Top
2Doggs View Drop Down
Platinum  (US)
USERID: 361228
HobbyKing aficionado
HobbyKing aficionado


Joined: 06/Dec/2010
Online Status: Offline
Posts: 203
  Quote 2Doggs Quote  Post ReplyReply Direct Link To This Post Posted: 01/Jul/2012 at 9:44pm
Yes, I just checked with my 80A SB - which to all intents and purposes is the same as the 60A, it just has more Mosfets (and I bought it instead of the 60A since it only weighs 2g more)

You could try setting LVC to 9v (3 lipo setting)since it seems like the voltage calibration on your unit may be off, if the logs are anything to go by. You might also experiment with different settings for current limiting. If it works with the lower LVC setting, though, you'll have to rely on timing your flights to avoid over discharging your packs.

Edited by 2Doggs - 01/Jul/2012 at 9:44pm
Back to Top
JoshyJS View Drop Down
Platinum  (DE)
USERID: 263106
Newbie
Newbie


Joined: 18/Jul/2009
Location: Germany
Online Status: Offline
Posts: 14
  Quote JoshyJS Quote  Post ReplyReply Direct Link To This Post Posted: 04/Jul/2012 at 10:27pm
The Hifei support sent me a diffrend firmware.
Now it works.
Back to Top
andrewju View Drop Down
Platinum  (RU)
USERID: 683452
Newbie
Newbie


Joined: 15/Nov/2010
Online Status: Offline
Posts: 2
  Quote andrewju Quote  Post ReplyReply Direct Link To This Post Posted: 31/Jul/2012 at 3:45pm
Hi All,

Has anyone tried to make a summary of firmware versions available? I think it could be useful, especially if we could also point out specifics of different versions.

I have a Superbrain 60A ESC and it came with firmware DTKA 2528 11MB 6004.
On the product page at Hobbyking (under files tab) I found these firmwares:
DTUA A108 11MB 6000
DTKA 2111 11MB 6002

I'm not 100% sure, but I think these are older than the one in my ESC.

Now, is there anything newer available?
Back to Top
andrewju View Drop Down
Platinum  (RU)
USERID: 683452
Newbie
Newbie


Joined: 15/Nov/2010
Online Status: Offline
Posts: 2
  Quote andrewju Quote  Post ReplyReply Direct Link To This Post Posted: 01/Aug/2012 at 12:05pm
Just got a message from hifei support that the firmware version in my ESC is currently the latest.
Back to Top
 Post Reply Post Reply Page  <1 13141516>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.54
Copyright ©2001-2008 Web Wiz

This page was generated in 0.328 seconds.