Please confirm your location:



USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > Turnigy

  RATED:

Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)

Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)

With v2 firmware update, correcting many flaws of the previous 9X, plus inbuilt 2.4Ghz (no daggy second antenna) this is a quality, reliable 2.4Ghz system suitable for beginners and pro pilots alike.
Get that locked-in feeling that only 2.4Ghz glitch free technology can provide.
Ultra fast reaction times and interference free control of your model is only achievable with this 2.4Ghz technology.

Without a doubt, the best value 9Ch system available!


Number of Channnel: 8ch ppm/9ch pcm
Display: 128*64LCD
Support Type: Heli/Acro/Glid
Support user: 8
Stick model: 4
Encoder type: ppm/pcm
Subtrim: Yes
Simulator Interface: Yes
Buzzer: Yes
Low Voltage Show: Yes
Required:
Battery
 
Included:
Turnigy 9x 9Ch Transmitter
Turnigy RF9X-V2 module
Turnigy 9X8C-V2 8-channel receiver
 
Important.
The TURNIGY 9X has been reflashed with the new v2 firmware, fixing previous menu and mixing issues. This firmware flash is only available from our TURNIGY 9X system as we flash each unit in our office before it is shipped.
Purchases of any other rebranded version of the TURNIGY 9X will not have the latest firmware and patches(even the OEM factory does not have these updates).
NOTE: "SWITCH ERROR" means you have one of the switches in the wrong position when you turn the radio on. It is not a fault.

* Special Offer Price, Limit of one per customer.


PRODUCT ID: TX-9X-M1

This product available from a warehouse near you!


Weight: 1375g
Quantity: 
International Warehouse
stock
10+
USA West Warehouse In Stock View Item
USA East Warehouse Out Of Stock
Price  $59.99

acc.
  • Turnigy 2650mAh 3S 1C Lipoly Tx Pack (Futaba/JR)

    Combo Price: $12.75   IN STOCK

  • Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)

    Combo Price: $59.95   IN STOCK

  • OrangeRX DSMX/DSM2 Compatible 2.4Ghz Transmitter Module (JR/Turnigy compatible)

    Combo Price: $29.95   IN STOCK



Further discounts available for registered & logged-in customers.
 Customer rated
5481
crowns
  
 
Total of 1512 discussions.
Jorge  13 points - 3/28/2015
 
Thank you NewToHobbyKing. Beginner quest: Using this kit would increase the TX range. I would like to have longer control distance with my Quanum Nova? 300 meters seems to be a short range.
Jorge  13 points - 3/28/2015
 
Some body knows if will work with Quanum Nova?
 NewToHobbyKing 15317 points
Jorge that is a BIG YES!
David  5 points - 3/27/2015
 
Is it Spectrum DS2 Compatible?
 NewToHobbyKing 15317 points
David as it comes No it is not. You can mod it and fit a different Module (Orange Dsm 2 / X Module). Then you can. But if you want Spectrum consider getting a 9XR and the Orange Dsm 2 / X Module.
Don  8 points - 3/25/2015
 
Thanks for the info. So with my limited knowledge of 2.4 Ghz systems, I assume that this transmitter will work out of the box with the included receiver ( I assume I can buy more receivers ) with no other additions, but if I want to use it with my existing Spectrum receivers, I have to buy the DSMX module shown in the ads?
 NewToHobbyKing 15317 points
Don Yes Yes but no on DSM, as it comes. You can mod it and fit a different Module (Orange Dsm 2 / X Module). But if you want Spectrum consider getting a 9XR and the Orange Dsm 2 / X Module.
Aaron  4 points - 3/25/2015
 
Will this work with a phantom v1
 NewToHobbyKing 15317 points
Aaron because the Phantom V1 uses a NAZA Flight Controller Board (FCB) you will be good. Now the FCB plugs into a Standard Receiver. If you are missing the FCB, (the NAZA Controller) then you will need a FCB and the Rc System above.
 n-nike 60 points
Aaron because the Phantom V1 uses a NAZA Flight Controller Board (FCB) you will be good. Now the FCB plugs into a Standard Receiver. If you are missing the FCB, (the NAZA Controller) then you will need a FCB and the Rc System above..Agreed.
 Octavio 1 points
i really doesnt understand your reply very well!!!!!!!!!!
 NewToHobbyKing 15317 points
Yes it will work with the phantom v1.
Customer Reviews
Review Blogs for this item
Bind Addtional Turnigy 9X 2.4 GHz 8Ch Receiver (V
Fabiomel
Bind the HK-GT2 3ch 2.4 GHz with the Turnigy 9X
Fabiomel
Bind Turnigy 9X V2 with HK TR6A V2 6Ch
Fabiomel
How To Increase Your TURNIGY 9X Radio Stick's Ten
MrRCFlyyer
Turnigy 9X REVIEW and SPECS
MrRCFlyyer
Batteries!
SUPER REMOTE
alhusam
Overall Rating
Straight Up
845 likes
ValueUNRATED
QualityUNRATED
53 thumbs up!
I bought this to supersede the HK-T4A transmitter. It comes as a bare transmitter - no batteries, no charger, no instruction manual, and no module (not even 72MHz). This is all OK, as I only use Lipo batteries, hate the cheap transmitter chargers, and ordered an Assan 2.4GHz JR-type module along with the order. Hobby King were up-front with all of this from the start, except the lack of a manual. The manual is available online, as the IMax 9, and the lack of a manual saved me further shipping dollars - a big factor in ordering something cheap.

The good news, it's not a cheap-feeling radio. The gymbals are really smooth, almost to the same standard as my Futaba 9C. Even the throttle ratchet is quite smooth, which is essential for heli flying. The case is plastic, but it feels nice in my hands.

Control with the Assan module was absolutely locked in. The availability of exponential restored my Shocky back to the smooth flying wonder I had originally built (with the HK-T4A I could not get it to fly smooth - I've become addicted to expo). The precision was also really noticable as I fed in gentle "tickles" on the sticks. Outstanding!

The misses (deduct one star):
IF YOU USE EXPO YOU CANNOT USE DUAL RATES!!!! Even 1pcnt of expo disengages any dual-rate settings, even though the rate settings are still there on the screen. I was initially really disappointed about this, until I realised that I hardly ever use dual rates. If you depend on dual rates, this is a FATAL


32 comments. Reply..

Overall Rating
wwmilan
636 likes
ValueUNRATED
QualityUNRATED
21 thumbs up!
This 9 Channel Transmitter is excellent, I am using this unit with the FRFRY 2.4Ghz module (JR compatible) and it work smoothly, I prefer the FRFRY over the Corona because the FRFRY is a TRUE Frequency Hopping system (very much like the FUTABA FAST) and is smoother on the servos, Also tested the Dual Rate and Expo and contrary to some reviews in my case work perfectly, remember to channel one at the time (expo or dual rate) and get out of the me


16 comments. Reply..

Overall Rating
EloPower
200 likes
ValueUNRATED
QualityUNRATED
12 thumbs up!
The transmitter is super. He works with Graupner / IR modules 35MHz/40MHz and Corona / TGY 2.4 GHz einwandfrei.I 've seen here
Manual?
http://www.skyrc.us/pdf/imax9x.pdf


6 comments. Reply..

Overall Rating
Jonas Mar
80 likes
ValueUNRATED
QualityUNRATED
4 thumbs up!
Today I received my Turnigy 2.4 G & Assan module, really very nice & good quality, I binded the two receivers to the module following the Assan instructions, it was very easy, excellent sistem at a very good price, thanks HK


3 comments. Reply..

Create an account
Overall Rating

45 likes
ValueUNRATED
QualityUNRATED
3 thumbs up!
Great transmitter for the money. I bought a Mode 1 and switched it to a mode 2. (HK was out of Mode 2 tx) Very simple to do.


8 comments. Reply..

.....click here to see all reviews
Aff. Link