|
7/11/2010
Peter (84%)
What are the real dimensions of this servo?
Is it 10mm or 13mm thick.
|
|
|
 |
|
|
 |
|
|
6/17/2010
Affamalg (75%)
I want to use them in a 1,5m aerobatic plane as aileron and elevator servo.
But i don't know if this works really good because the look more like glider servors....
THank you!
|
|
|
| |
|
kd6jes Jim
(38%)
They have pleanty of torque,almost 50 in/oz.This is about the same as a standard size servo.Also they have all brass gears except the output which is aluminum.It also has a top ball bearing.Only the mounting is different
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Affamalg
(75%)
One more Question: Have anyone tested them with a 35mHz System (I use Graupner)?
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Affamalg
(75%)
One More... :)
Could anyone who has the servo lying around, measure the dimensions exactly? Please also the mountings at the sides...
This would help me very much!
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Michael
(42%)
i would not see a reason why not to use them on aerobatic planes. i have them in 1,5m full carbon F3F glider for slope soaring. flying with high speeds - huge airerons result in heavy servo loads.... no problems with them. als the speeds are slower in motorplanes i would give it a try...
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
stan
(84%)
You can use these in your plane without any doubts. I use them in Piper J-3, 1800mm as ailerons / flaperons. The servos working flawlessly. Stronger then standard size HS-422.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
3/11/2010
Michael (42%)
someone wrote these servos will not work with futaba 2,4GHZ FASST system?
Any particular explaination fot than phenonenon?
Another User wrote in his Review that the Servos work perfclty with his Futaba FASST R617 - Reciever:
So whats true now?
|
|
|
| |
|
fliegerpez
(46%)
Hallo,
all i have to say, these are working with the R617 perfectly!
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Michael
(42%)
recieved 2 of these. work perfectly with futaba R617. no worries...
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
fraspeed
(53%)
this is working on futaba 2.4, very well
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Michael
(42%)
works fine with FASST reciever !!
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Rene
(63%)
They work perfect with the 617 receiver but not with the 608 and 6008 receiver.They only work with the 608 and 6008 receiver when you put the transmitter on, and the RX in on position,and if you then put the servo's in the receiver,then they wil work.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
12/30/2009
Maciek (50%)
Super servo. Servo according to me better from HS -125.
|
|
|
|
|
|
|
|
12/25/2009
hillflyer (46%)
Has anyone measured the current consumption of these servos under load?
Have you had problems using them with a PPM (FM) receiver? Thanks for any infos!
|
|
|
|
|
|
|
|
|
12/6/2009
astir (87%)
Guys, I did some more testing to exclude possible low pulse voltage (2,8v) on older Futaba receivers. I connected servo to newer receiver (3,2v puls height) and via and EMCO TEC DPSI. Results ae the same. Servo won't work ! It drives me nuts
|
|
|
|
|
|
|
|
|
11/29/2009
astir (87%)
Anybody an idea how to get these work on a 2.4 GHZ Futab receiver. They only work if you connect them after powerup of the receiver.
|
|
|
| |
|
Rene
(63%)
they work perfect with 617 fasst receiver
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
9/4/2009
ste92 (50%)
Do they work with Futaba 2,4ghz FASST rx system?
Thanks.
|
|
|
| |
|
astir
(87%)
Ste92,
NO they do work with 2.4 Ghz Futaba. I ordered 5 and are all useless. They only work if yiu connect them to the receiver after it has been powered on. Makes these servo's useless.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
fraspeed
(53%)
Yes, i'm using 10x of these
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
5/13/2009
kd6jes Jim (38%)
I received an email today May 12,saying they were back in stock.When I went to order them it showed -8.What gives?
|
|
|
|
|
|
|
|
4/25/2009
manu42 (84%)
when are they back in stock ?
|
|
|
| |
|
paul
(77%)
The thickness of this servo? Is it 10 or 13mm There are both versions at "Dimensions and produkt Table"
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Son of Paleface
(92%)
Its 10.3mm thick.. very smooth
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
