|
26/07/2010
Thiruselvam (10%)
When the shaft breaks, we will lose the small spacer washer and the PTFE washer (If used) that is under the c-clip.
I think HK should include this as one of the items in the accessories.
|
|
|
 |
|
|
 |
|
|
25/07/2010
sklenar (79%)
I like this "style" of motors, I found them running smoothly and efficient, however, I miss data about them.
Please, write "No load current" at any voltage. It is very important for certain applications.
TIA
|
|
|
|
|
|
|
|
|
22/07/2010
Rajakumar (50%)
Are the accessories shown in the picture above included in the order of 1 motor?
|
|
|
| |
|
desiclad maafia
(100%)
Yess Mr Raja....entire stuff is standard with motor...I have recently got five of these motors.....
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Thiruselvam
(10%)
Yes.
You will get a full set of acessories as shown.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
24/06/2010
galenm (50%)
I have had the winding post loosen from the base and then the motor can wobble. I have tried dropping some CA where the post meets the base. Not sure how long this will last.
|
|
|
| |
|
Thiruselvam
(10%)
I use this on my Quadrocopter and I get this problem too after a major crash.
As the winding post also holds the shaft to the base, it would be impossible/dangerous to run the motor again if it's not secured.
I will remove the winding post, that comes out together with the bearing. I will clean the bearing and also the base. Then I will apply some steel filled epoxy (I have tried quik-cure epoxy too but it's not strong enough* comes out after a minor crash) and push in the parts together. Wait a day and the motor will be as good as new.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
14/09/2009
SG-1 (97%)
hola!!! buen motor para el parkmaster,tiene mucha potencia,perfecto para 3D,helice 11x4,7
salu2
|
|
|
|
|
|
|
|
6/04/2009
kerrylaw7307 (62%)
is the shaft revesable? meaning can I reverse the shaft so I can mount the prop on the other end?
|
|
|
| |
|
Beaufighter
(25%)
Don't know if it is reversible shaft, but I use the included propsaver (or collet adapter) if I want the prop on the "shaft" side, and the included threaded, screw mounted "reverse" prop adapter if I want prop on "bell side". Only downside is that you loose ablity to use propsaver is you fit the motor "backwards".
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Beserc
(84%)
Yes, the shaft is reversable. I tried on the smaller 2205, so it must be the same.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
AlfaHX
(-37%)
I've tried to reverse the shaft but no luck.. you need to slit a tiny gap at near to tip of shaft so that the C clip can fit in and hold motor together. I think It's hard to machining because it's a hardened steel shaft.
If you can find a way to reverse the shaft please write here.
by the way this is really perfect motor. Using it with 11x4.7 sf propeller with 3s lipo. I Did'nt measured but I thik It pulls about 1000gr-1300gr! After 10 minute full throttle at the bench motor did'nt even get warm.
Only thing with motor when you throttling, if you decrease throttle sometimes it makes a quiet clicking noise. I don't know why and where the sound comes from but it does'nt effect motor, it works perfect.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
taffy_magic (75%)
if i use this motor in a mini ultra stick what prop and esc u recommend
|
|
|
|
|
|
|
|
virgelis (50%)
Can I order spare shaft for this motor
( Turnigy 2217 20turn 860kv 22A Outrunner )
|
|
|
| |
|
RCER88
(24%)
Hey Virgelis they sell a kit that has a spare shaft.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
tnitzani (81%)
what is the distance between the screws on the motor mount?
|
|
|
| |
|
swessels
(60%)
Normally you have a pair of holes of 16mm diameter and a pair of 19mm diameter at motors of this size. Tjhis is to fit the mounting holes of the old 400 and 600 sized brushed motors.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
.jpg){kind=small}
