Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Speed Controllers > All Speed Controllers
> Speed Controllers > TURNIGY ESC
> Speed Controllers > Under 20 Amp
> Multi-Rotors & Parts > Speed Controller > Turnigy Plush

  RATED:

TURNIGY Plush 10amp 9gram Speed Controller

TURNIGY Plush 10amp 9gram Speed Controller

Plush 10A Brushless Speed Controller
The Plush series of ESC are a very good quality controller with a broad range of programming features and smooth throttle response compared to other BESCs in the same price range.
These escs have linear throttle curve and can handle 10A continuously.

Cont Current: 10A
Burst Current: 12A
BEC Mode: Linear
BEC : 5v / 2A
Lipo Cells: 2-4
NiMH : 5-12
Weight: 9g
Size: 27x17x6mm
User Programmable, both via controller and optional programming card. The programming card is an excellent item as it instantly tells the user the current settings and with a few simple clicks of the buttons, the user can change the settings and have graphical reassurance of those changes.
The programming card is an excellent item and simple to use! Much better than Jeti or similar programming cards.



PRODUCT ID: TR_P10A

This product available from a warehouse near you!


Weight: 20g
Quantity: 
International Warehouse
stock
10+
USA West Warehouse In Stock View Item
USA East Warehouse In Stock View Item
Price $9.40

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
5597
crowns
  
 
Total of 68 discussions.
RonRC  3705 points - 10/7/2014
 
I paired these ESCs with the FC 28-05 2840kv motors and 6x3 props to get my UFO flying. I finally went to a KK2 board to keep it level. originally had the i86 on it.
chrismog  23 points - 10/1/2014
 
I have a set of 4 of these. My question is why am I getting a 3.25v reading on all the signal wires? I am getting the correct 5v between ve & -ve so why am I getting this strange voltage between the signal wire and the -ve?
 reset-leo 92 points
I'm not a real expert on that, but from my understanding, you'll not be able to read the operating voltage from a signal wire, since the signal isn't a constant positive current, but needs to carry the information in - very baldly spoken - a certain sequence of varying voltage levels. got the idea? imagine a signal with two different states: high level of 5V and a low level of -5V. now, imagine that by chance, one piece of information is made of a high-low sequence and the communication is steadily transmitting that information. in this example, that would be similar to an active current switching between 5/-5V and therefore not giving you any reading (when you try to measure DC). now, the signal used for this ESC is a PWM signal, which is a bit more complicated than my constructed example and not that deterministic in the result you may get on a DC measure.
BEST ANSWER CREDIT AWARDED
Craig  1 points - 9/29/2014
 
I'm just getting in to electric. Does this controller come per-programed or is this something I will have to learn before I can fly?
 Napstr 1169 points
Hi Craig This controller and all others come pre programed - so you simply solder to your motor plug into your reciever, solder on a battery plug (to match your battery) plug the battery in and it will work (is factory set to lipo mode and if your throttle stick is in the low position will beep the number of lipo cells connected)
 r_g_r 1334 points
It comes pre programmed with some defaults that should fit many people. Never the less you should always double check the settings and make sure they fit your needs. I'll link in a video below that shows how to check and change the settings of this (and many other turnigy ESCs)
 r_g_r 1334 points
Hmm, somehow the video does not show up for me. Search on youtube for "Turnigy Throttle Stick Programming" to find the video.
Umayir  28 points - 9/3/2014
 
hi guys, I bought a micro cessna 182 rc airplane, the esc on that plane was 6A.... it burnt out... so will it be possible for me to replace this esc with my cessna 182... btw the motor for the cessna is 2600KV..?
 r_g_r 1334 points
Yes you can replace it. The amp rating of the ESCs must not match. As long as the new ESC can handle at least the same amps as the old one you are fine. So no problem here. But you should check that the physical dimensions of the ESC are also OK. Usually ESC get bigger the more amps they can handle. So just make sure that this ESC fits into your airplane. This one if really tiny, so I guess it should not be a problem.
BEST ANSWER CREDIT AWARDED
 Umayir 28 points
by the way, what is w/bec?
 Napstr 1169 points
Hi Umayir Definitely no problems to replace the ESC and these are very good ESC's. the w/bec just means with bec (battery eliminator circuit) which just means that the ESC will also power the receiver and servos from the main flight battery.
 Umayir 28 points
thank you so much...!!
Norm  9 points - 6/7/2014
 
I ordered these to replace one that got burned out. I cannot get the new one to calibrate with the old ones. Is it a different flash? These are the exact same part and the exact same numbers, but do not calibrate with my first ones. ANyone have any ideas?
 WillemP 32 points
Are the other 3 ESCs flashed with a custom type of firmware, for example SimonK?
Customer Reviews
Overall Rating
Big Ern
60 likes
ValueUNRATED
QualityUNRATED
16 thumbs up!
Control caught fire upon hooking it up to a 11.1v 500mah lipo. Wouldn't you know it burst into flames. The shipping to send it back would cost more than buying a new controller. Crap.......


21 comments. Reply..

Overall Rating
Pablo Otero
likes
ValueUNRATED
QualityUNRATED
13 thumbs up!
This is a great ESC, but it only last about 4 flights working OK, then it failed with more than a 3 Amp load, it cut-off, this is working with a 2s lipo pack that have verify its charged and failure its constant, when power drawn its more than 3 amps it cutoffs, also i have verify voltaje and its steady at 8.0 volts and lipo detection its of 2 cells. Maybe bad luck of defective unit.


4 comments. Reply..

Create an account
Overall Rating

59 likes
ValueUNRATED
QualityUNRATED
13 thumbs up!
Not impressed, it worked like a 3 speed transmission. This is the only Turnigy plush ESC that was not a 5 star. maybe I got a bad one??


1 comment. Reply..

Overall Rating
Patrick Schindler
likes
ValueUNRATED
QualityUNRATED
11 thumbs up!
Very good value. I will buy again.

Replaced wires and removed heat shrink to get down to 6.5g w/micro deans and standard servo connectors.

Only problem is that the startup from a dead stop takes about 1 full second. A quality ESC (think PH10) will start up instantly. This makes 3D a little difficult.

Other than that it is great value.
I smoked my evaluation unit already but I was driving it hard.

Way better than the Tower Pro 9g.

Read my review on the Tower Pro 9g ESC as the current firmware version has a major flaw. (LVC is set to 2.7V/cell causing full 2S pack to register as dead 3S pack)

Buy this ESC instead of the Tower Pro if you want to go 2S

-methods


1 comment. Reply..

Overall Rating
Paris Cockinos
likes
ValueUNRATED
QualityUNRATED
4 thumbs up!
Great esc better than most esc great esc for hextronik 24 gram on 2s and 3s. with 9x6 prop.
Love it
Thanks


No comments. Reply..

.....click here to see all reviews
Aff. Link