Please confirm your location:

Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Electric Motors > TURNIGY
> Electric Motors > Outrunners by size > .15 - .40


TR 35-30C 1100kv Brushless Outrunner (Eq AXi 2808)

TR 35-30C 1100kv Brushless Outrunner (Eq AXi 2808)

TURNIGY AerodriveXp

Model: TR35-30C

Input Voltage : 7.4V~11.1V (2~3S Li-po)
KV : 1100 rpm/V within 10%
Max. efficiency current : 10~15A
Dimentions : 35mm X 30mm / 1.38in X 1.18in
Shaft diameter : 4mm / 0.16in
Weight : 77g / 2.72oz
Number of poles/magnets : 14
Recommended model weight : 600~1300g / 21~45oz
Power equivalent : .12,2stroke
Stator Dimentions: 28-08

PRODUCT ID: TR35-30C-1100

This is an archived page. This product is no longer available and has been replaced by a newer product.

Kv(rpm/v) 1100
Weight (g) 0
Max Current(A) 15
Resistance(mh) 0
Max Voltage(V) 11
Power(W) 0
Shaft A (mm) 4
Length B (mm) 30
Diameter C (mm) 35
Can Length (mm) 13
Total Length E (mm) 49
Update/Add my own data
Customer Data
Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
Total of 67 discussions.
Antonio  1 points - 2/19/2012
Que helice para avió*n con este motor de 1250 gr
Juanes  59 points - 1/12/2012
Some one know the thrust that it have with 11x4.7 and 3cell bat??
 Romio 9 points
the thrust that it have with 11x4.7 and 3cell bat is about 1200g.
 miguel 5 points
it'd depends of the propeller, is not the same (or close) a gws and an APC propeller, in this web you have some data and test of this
ALCARAFA  343 points - 11/17/2011
Any of you guys know how many winding turns this motor have ? I want to rewind mine, factory guys put tons of epoxy into it, impossible to find out how many turns it had.
 kobuscl 6 points
i rewind n axi2808 with 17 winding workink fine
Ali Raza  22 points - 10/21/2011
what is the best configutration for this motor? for exmple 9*6 APC-E and 3S 2200 lipo it can be?
 munsaf 301 points
It depends on your plane style and asked speed ! The 10x5 don't work at all on my 1 meter F3A plane which need speed. For this plane the correct propeller is 9x7.5 APC-E. A 3D plane will be ok with lower pitch and bigger diameter.
 Jean-Mi 27 points
Same for me ! Use this engine on a F3A 1 meter plane with 3S 2200mAh Lipo 9x7.5 APC-E prop and it's a pleasure !
Javier  1 points - 10/13/2011
How is the right form to install the proppeller?
 rwallage 105 points
You can either use the supplied hardware (if you install the motor using the suoolied backplate), or you can get a prop adapter. The collet-type adapters are best.
Customer Reviews
Overall Rating
152 thumbs up!
I owned two warp 6 motors before testing this one.

All I can say is that it's a GREAT motor. Here're the tests I did with a wattmeter and some props on my minimag

Plane : Multiplex Minimag
Lipo : 3S 2200 mah 20/30C
ESC : 25A

Propeller : 7x5 APC E
Amps : 8,7A
Watts : 100W

Propeller : 8x6 APC E
Amps : 13,7A
Watts : 146W

Propeller : 9x7.5 APC E
Amps : 19A
Watts : 196W

Propeller : 10x5 APC E
Amps : 13A
Watts : 137W

Propeller : 9x9 APC E
Amps : 20.5A
Watts : 207W

Propeller : 10x10 APC E
Amps : 24A
Watts : 235W

Highly recommended.

2 comments. Reply..

Overall Rating
Brian Mihalka
110 thumbs up!
I purchased this motor to install in my new Precision Aerobatics Addiction 3D plane all up weight = 27oz. or 765 g. I am using it with the Turnigy Plush 30amp Speed Controller, 4-HXT900 servos and a Thunder Power 2100mah Prolite lipo. I have tested this motor with a APC 11 x 4.7SF and APC 12 x 3.8SF props. The APC 11 x 4.7 pulls peek of 30.27 amps but quickly settles down to 28.51 amps @ 11.1 volts. The APC 12 x 3.8 pulls peek of 33.36 amps but quickly settles down to 31.56 amps @ 11.1 volts - both tests are at full throttle on the ground. In flight I have flown both props for 10 min doing about the same 3D stunts and found this motor to have unlimited vertical climbing power and running around 110 deg after a flight with the 11 x 4.8SF and around 126 deg after a flight with the 12 x 3.8SF props. This motor runs VERY smooth and quiet. For the price, I should have purchased more even if I had nothing else to put them into! If you are into 3D flights and have an aircraft around the same weight as mine, you will not be disappointed.

5 comments. Reply..

Overall Rating
84 thumbs up!
Measured on Chauvin Arnoux C.A 27, Kaise sk-7720
U = 12,5 V I = 1,2 A f = 13080 RPM / KV = 1050 ot/V

GWS HD 8x4 3-blade:
U = 12,0 V I = 11,2 A f = 11700 RPM

Master Airscrew 8,5x6:
U = 11,6 V I = 18,5 A f = 9300 RPM

APC 9x4,7 SF (prop overloaded!):
U = 11,7 V I = 16,2 A f = 9750 RPM

APC 9x6 SF (prop overloaded!)
U = 11,4 V I = 24,0 A f = 8080 RPM

"APC" 9x6 E (from HC/UH/HK):
U = 11,5 V

No comments. Reply..

Overall Rating
37 thumbs up!
Motor runs very well.

Measured data with Eagletree 3 on 2100 mAh 3s and APC 10*5:
10.5 V, 19 A, around 200 W input and 1000 g thrust

No comments. Reply..

Overall Rating
33 thumbs up!
This sounds like an awesome motor. I would like to inform some of the people who have posted here that: Watts= voltage times amperage. So 190W does not equal 10A times 11.1 volts. I imagine this motor is capable of: 11.1V times 17A = 188.7W continuous, and probably 14.8V times 25A = 370W burst.

2 comments. Reply.. here to see all reviews
Aff. Link