TURNIGY TRUST 45A SBEC Brushless Speed Controller (AUS Warehouse)

Total of 6 discussions.

brendan

2 points - 1/29/2013

Will this work with a 3647 Brushless outrunner (700KV). With a turnigy 9x transmitter? Might seem silly but im new to this and injoy hobby king purchases. thanks carpo

Julian800

2 points

Sorry, you can't use this one. You need a speed controller over 60 A. Use the 75A . That will be safe option.

James G.

18 points - 6/29/2012

can be installed under the battery holder on a 450 pro V2?
please can someone measure it?

DanielW

41 points

no it doesnt fit! also after my experience with it make sure the BEC is working correctly in it or you may lose signal several times causeing loss of heli!

daz79

1 points - 5/16/2012

Do the connectors to motor require soldering?

Scott

234 points

No, it comes with bullet plugs already soldered on!

BEST ANSWER CREDIT AWARDED

Wayno1970

7 points

Mine did not have plugs, had to solder to my own connectors. Hope this helps

Doug

7 points

Seems that they are 3.5mm plugs too just FYI (I ordered 2mm and 4mm plugs and they are too small and too large!) I also have had much trouble de-soldering the wires from the esc to attach longer cables (as I couldn't make extensions with the bullet connectors I have) as the solder used seems to have a high melting point. Had to cut and trim and solder over original solder. I had less difficulty melting the solder on the bullet connectors attached as the surface area is much smaller but still tricky...

Joel

97 points - 4/11/2012

hey, everytime i plug my battery into this esc its inactive, but once i hold the throttle on, it beeps for 3 seconds and then the motor just starts running even once i throttle off... every time i connect my battery i have to do this, and my motor runs automatically.. someone please tell me how to make this esc plug and play.. it seems im entering programming mode or something... someone please help

Flying V

81 points

Is your throttle fully off or reversed? Try using the trim to lower the start point for the throttle. It usually goes into programming mode if the throttle stick is engaged fully, so maybe it is reversed at the radio. Try reversing it?

ElectricAussie

2780 points

Hi Joel, This sounds like you haven't programmed the throttle range on the ESC. Set the throttle range as follows: 1) Turn on TX. Make sure throttle trim is set to zero. Move throttle to max position. 2) Connect ESC to battery. You should hear 2 beeps. 3) Move throttle to off position. You should hear ESC go thru its normal startup sequence. 4) You're done, go fly! Cheers!

Owen

21 points - 1/5/2012

OK what is the special card to use????

Dallas

5 points

You dont need a programing card to program this esc the card is to keep track of settings. program this esc with your tx and instructions supplied.

jason

7 points - 10/21/2011

Can this esc be programed with the plush programing card?

maverickss40

69 points

yes , it can...only k-force can't

Owen

21 points

Krap, this esc can't be programed with a card I tried 3 different cards never worked.

scouttman

8 points

you need the special Turnigy Trust SBEC Programming Card it's made especially for the trust series

flying hi

2 points

which card is needed to program this ESC?

Customer Reviews

Overall Rating		HYCRYPOTES 54 likes
Value
Quality

Like it?

Davvero un ottimo regolatore. L'importante è comprare la scheda per programmarla, in questo modo è più semplice cambiare i parametri. Ottimo rapporto qualità prezzo, ve lo consiglio.

No comments. Reply..

Overall Rating		Docspace 156 likes
Value
Quality

Like it?

Excellent ESC have purchased 6 of these so far an not a problem with either of them ,running in my Helis 450 series,Park Flyers,Skyfun Jet an they all work like a Treat,Great Value for your Money these days 5stars buy em their Good

No comments. Reply..

Overall Rating		groden 14 likes
Value
Quality

Like it?

I am using one in a bixler, overkill for stock but with motor and prop upgrades it is worthwhile. It is quite big for 45a esc but overall I would buy again.

No comments. Reply..

Overall Rating		Anthony 4 likes
Value
Quality

Like it?

just got this esc no lead ends on battery side but bullets on motor side . will be fitting to a hk 450 gt pro more when i have it all together

No comments. Reply..

Overall Rating		Yeswecan 146 likes
Value
Quality

Like it?

Good value esc. A little thick for a 45a due to the oversized heatsink. Cut away part of the shrink wrap to expose the HSink,looks good and more effective. Tested for 5 flights with a 500w NTM motor,4 corona digital servos with cx3x1000 fbl gyro.Flight time 7-8 mins, esc warm to hot. Reduced heat with separate BEC. Works great.

No comments. Reply..

.....click here to see all reviews