USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
Turnigy Typhoon 600H Heli Motor 1100kv (600 class)
The Turnigy Typhoon is a very serious upgrade for any 600 size heli. Big, tight copper wire turns with thin, tightly packed laminations and a small stator/magnet air gap make this motor very efficient and powerful. Users will notice the instant power increase and higher idle speed when using this motor & we suggest you adjust your throttle accordingly.
Specifications:
Dimension: 42mm x 62mm, 85mm(with shaft) Weight: 269g Kv: 1100rpm/V
Voltage: 3~6S Max Current: 60A
Diameter of shaft: 5mm Length of front shaft: 23mm ESC: 80A
The Typhoon 600 Size helicopter motor is a serious upgrade for any 600 size heli.
1.What is Idle current?
2.It is given here ESC 60A, does that mean that the maximum current that can flow thruogh the motor is 60A.
3.Also what propellers to use ....... basically how to calculate the lift or thrust due to the motor?
Please help....
Im pretty sure this motor is good for 550 to 600 size helis. I had it in my 600 and was nice for scale flying. Its not a powerhouse, but good motor to start with
I used this motor on my 600gt and it was great. I used the turnigy opto 150 amp esc. Its a bit of an overkill, but i recomend having more than less so u dont fry any of your electrics during flight
I suggest you lok now,because there are in stock now. Try stock alert when you need a products and HK will send you an E-mail when they restock.Hope this helps
For the heli i use ever medium-hig timing because it work in high revolutions.
The motors of helis are the sustentation of this.
Please credit me if this is useful
You have 6s lipo? if yes following is the right way:
you only have to change the gear to increase your headspeed. If you have the HK600GT your maingear is 170teeth.
with an 15tooth pinion you get at 100pcnt speed 2185headspeed. With an HK600GT you di not need 2000headspeed. 1900 is enough.
I am having the same issue...very low head speed...stock maingear,13 tooth pinion,150 A k-force esc 6s battery....whats the best timing for the typhoon 600 motor...changed the pinion without success
Hi there, I found that the genuine trex 600 is supposed to use 5mm pinion gears. Hobbyking only stocks 6mm pinions that do not fit the 5mm shaft on this motor. So your best bet is to find a place that stocks align trex parts. Try looking online, the US is good
google 5mm 0.7m pinions. I bought a set of Rhino pinions which came with two each of 12,13,14,15 tooth pinions. Only cost ~$10. I would however like to find a 16 or 17t pinion to run a slightly higher head speed.
I have the hk600gt set up with typhoon600h 1100kv,hk 70/80 esc, had to switch out main gear for KDE 164 tooth gear and 15 tooth pinion. 6s battery is getting hot and puffy,esc is also getting hot (only hovering). tried timing at 1',7',15' degrees no change. soft start jerky. am i loading up with the gear and pinion? Does anyone know how many poles on 600h 1100kv? What is mod on pinions? **** And just for reference the KDE gear is awesome no noise and absolutely true.
I have a similar set up to you, turnigy typhoon 600h and a the opto 150amp speedy. I am running the stock main gear but changed the pinion to a 13t. Also the motor is 2 pole. The motor on my heli draws around 60 amp with bursts of upto 100 amp, maybe why your battery and esc are getting hot, might need a bigger esc
F
or my HK600GT with lot of Align parts. Turnigy 85A esc, 15T pinion, 6S 5000mah 40C turnigy lipo: 7min of cool and nervous flying, and motor, esc and lipo just a little little hot. No puffing lipo, and lipo have 50 flights !
I love my 600GT, and this motor ! I have the same serie on my HK500GT with Airwolf align fuselage, and i have the same serie on my HK450V2. No problem with all of these.
Will this fit in the Raptor 620E? I need the mounting hole dimensions to know for sure. The KV rating looks a little high for the Raptor gearing 11T or 12T/111T. How does this motor compare with the Zpower 50A?
The specifications on this motor regarding the number of magnetic poles are not specific but it does come highly recommended from all of the heli forums. See motor specs in summary: Big, tight copper wire turns with thin, tightly packed laminations and a small stator/magnet air gap make this motor very efficient and powerful.
It's completly false!
Please don't reply if you don't know or not sure.
With 12 poles the rpm was only 1700 instead of 2070.
The correct number of pole is 8 !
PS. I will try this motor on my Gaui 550
You can put auto/normal/medium or even Low. Higher is the timing higher the motor will be hot. I dont advise to put the timing on high with this motor.
Frequency PWM on 8khz or auto outrunner.
Hello,
10 tooth means less heat and battery consumption for this motor.(with 6s).Because motor has less torque and high rpm than other sales.My offer is use 10tooth i am also using on my hk600.
I used this on my Trex 600e with 13 tooth pinion, performance as good as original trex 600e stock motor. You might strip main gear with 10tooth pinion.
it depends , what do you want most ?
more headspeed and more stability but less flyingtime then go for the 13 or 14 tooth pinion.
if you want to do some scale flying with scale blades whch require lower headspeed and want a longer flight time then the 10 tooth will suit your purpose
I use the 13 teeth pinion which gives nearly the same rotor speed as with Align XXL motor and 10 teeth pinion. Seems to be the good choice ... for my (cool) way of flying !
This depends greatly on what type of flying you want to do, you are aiming at high head speeds this means VERY responsive and extra strain on blade grips, bearings and head assembly. Mine has plenty of grunt with the 12 tooth pinion! :-)
A very efficient option (above 80%) would be a 17T pinion with a 5s battery (perhaps 2 x 2200mah 5s). I don't how easily obtainable a 5mm 17 or 18T pinion would be.
The "Turnigy Typhoon 600H Heli Motor" needs a 5mm pinion.
If you bought a HK600 Heli kit, it will come with a 10 tooth pinion.
Hobbyking does not stock any 5mm pinions other then the 10 tooth.
I recommend searching other sites for a 5mm 13 or 14 tooth pinion.
The 5mm or the 6mm refers to the size of the motor shaft....in the case of the Typhoon it is a 5mm shaft, they are NOT interchangeable. The 5mm will not go on a 6mm shaft and the 6mm will be VERY sloppy and off centre on a 5mm shaft.
Hello everybody,
where can one find pinions with a 5mm shaft (Align uses 6mm) AND the correct pinion modulus (0.7 I beleive to be compatible with the T-rex600 main gear)???
Thanks
I put a rhino 15T pinion with a 6S pack. Double check and tighten the grub screw into the slot on the shaft using loctite. Mine came loose on the first flight.
if you think your going to do some 3d with this thing don't be disappointed when it bogs and your tail blows out on any full cyclic input with any other collective input.
60*22.2=1332watts which is very low for a 600 size heli
realistically if you are going to do any 3d flight with this thing you will need at least 2000watts constant current to maintain but even then it likely won't take a beating.
TrevJonez i think your answer is the best.
For a long time i am reading what people say about different motors for 600 heli and after ordering mine i realised that things are as you say.
This motor with 10 or 13 pinion cannot provide enough power even for sport fly.Tail gets really unstable.I will try it with 16 pinion and see how it wiil go,
If the result is not the expected the i will heve to buy a more powerfull motor
Customer Reviews
Overall Rating
Pygar
155 likes
Value
UNRATED
Quality
UNRATED
2 thumbs up!
I use the standard T-rex 100A ESC. To avoid shaking at startup, I had to put ESC in "low timing" mode. This setting is used for Align two pole inrunner motors. If it had 100A max current it would be a 600 helicopter upgrade. With 60A max current it will handle sport flying but not 3D. A good first motor for your HK-600GT, not a powerhouse. Absolutely good quality for your bucks.
No comments. Reply..
Overall Rating
jaspers
6 likes
Value
UNRATED
Quality
UNRATED
1 thumbs up!
I use it in my speedboat and gaupner GTX 800 and a 60A esc on 6s lipo and hardly gets warm great engine http://www.youtube.com/watch?v=eYL3UwSTtRU
4 comments. Reply..
Overall Rating
Itashi
114 likes
Value
UNRATED
Quality
UNRATED
1 thumbs up!
Exelente motor para o HK600GT ! uso e recomendo !
1 comment. Reply..
Overall Rating
Pete47
98 likes
Value
UNRATED
Quality
UNRATED
1 thumbs up!
pcnt star for providing a motor for the HK 600. please stock up I'm sure many more people wanting 1, reserve 1 for me please
No comments. Reply..
Overall Rating
Micho69
176 likes
Value
UNRATED
Quality
UNRATED
1 thumbs up!
Tento motor ma najlepsy pomer co sa tyka ceny/hmotnosti a vykonu. A jeho otacky dovoluju jeho použitie nie len vo rc vrtulniku ale aj v rc lodi alebo v rc autach. Vzdialenost otvorou na šrouby je 25 a 29 mm.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg)
.jpg){kind=small}
.jpg){kind=small}
