HobbyKing Forums
Forum Home Forum Home > Product Specific > Transmitters and Receivers > Assan
  New Posts New Posts RSS Feed: Binding plug Assan receiver
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Binding plug Assan receiver
 Post Reply Post Reply Page  <12
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
fmorais View Drop Down
Platinum  (IE)
USERID: 7644
Bargain Addict!
Bargain Addict!


Joined: 14/Apr/2009
Online Status: Offline
Posts: 31 		  Quote fmorais Quote  Post ReplyReply Direct Link To This Post Posted: 18/Feb/2010 at 10:22pm
Hi,

I just got my kit yesterday for my 9C radio.
At first I was having the same problem, it would turn from Red to Green no matter if I moved the elevator stick (chann 2) or not.
After, I noticed I was using in the radio a memory for a heli that has reduced endpoints.
I then changed to a plane memory where I knew I was using 100% end-points and a slight move of the elevator up/down made the TX switch to binding mode.

Hope it helps.
Nando
Back to Top
vasy1 View Drop Down
Platinum  (US)
USERID: 15488
HobbyKing aficionado
HobbyKing aficionado
Avatar

Joined: 10/May/2009
Location: Canada
Online Status: Offline
Posts: 1064 		  Quote vasy1 Quote  Post ReplyReply Direct Link To This Post Posted: 18/Feb/2010 at 10:31pm
Originally posted by bruce

I have the same problem exactly using an Opic 6 Transmitter with a Assan rf unit and a Assan receiver with the transmitter in PPM mode.
I get the green light on the transmitter module but the receiver just flashes red like yours
Can anybody offer any advice.
regards
Bruce


Green means your TX is NOT in the bind mode. You gotta turn the transmitter and move elevator up down twice I think and TX will go into bind mode which is red blinking if I remember correctly. Make sure your up/down is not reversed or you wioll need to go down up and make sure EPA is set to 100%, not any other number, also remove expo and set duel rate to 100%.
Back to Top
reefpilot View Drop Down
Platinum  (NZ)
USERID: 352438
Bargain Addict!
Bargain Addict!


Joined: 03/Nov/2009
Location: Christchurch NZ
Online Status: Offline
Posts: 24 		  Quote reefpilot Quote  Post ReplyReply Direct Link To This Post Posted: 26/Feb/2010 at 11:17am
Hi guys, incase you are still having problems I have been having the same till I figured it out.
RX turned off turn on TX as soon as you turn on TX move your aileron stick if you wait to long it will not go into binding mode . if it does not go into binding mode turn tx off and start again turn on and move the other stick.
If you look at the module when you turn on the light will be red move the stick and it will go to bind mode if the led turn green you are too late moving the stick.
Anyway hope that's of some help.
Rgds Paul
Back to Top
chewy View Drop Down
Platinum  (MY)
USERID: 7380
Bargain Addict!
Bargain Addict!


Joined: 09/Mar/2009
Online Status: Offline
Posts: 67 		  Quote chewy Quote  Post ReplyReply Direct Link To This Post Posted: 08/Mar/2010 at 3:59pm
Ok,

Whether it is the elevator or aileron stick depends on whether you are using a Futaba/Hitec or JR/Sanwa tx respectively.  Channel 2 is assigned differently between the 2 types.

Make sure the channel 2 trims/subtrims are centred, the EPA or ATV is set to at least 100% and mixing (such as elevon etc) are off.

Then get the rx ready with the bind plug alread in position.  Turn of the tx and quickly move the ch 2 stick up/down or left/right depending on the type of tx (Futaba or JR).  You must move the stick fully and keep on moving until your tx has fully initialized and the module's LED has turned red (blinking?-don't remember).  Now plug in power to the rx and the rx's LED with blink red for a short time and then turn steady green.  The tx module will also turn green, I think.  Switch everything off and you are done.

Remember, the rx reads the tx stick/switch/knobs/dials positions when power is applied to set the failsafe.  If the rx should lose the signal, it will go to this failsafe position.  So, if you happen to program an esc by turning the rx on with the throttle stick all the way up.  After programming you MUST switch off the rx and then back on with the throttle stick in the normal down position.  Otherwise, should anything happen on that flight, your plane will jet itself right to the next county!

chewy
Back to Top
mikelleen View Drop Down
Platinum  (US)
USERID: 100832
Newbie
Newbie


Joined: 07/May/2010
Online Status: Offline
Posts: 2 		  Quote mikelleen Quote  Post ReplyReply Direct Link To This Post Posted: 11/May/2010 at 11:00am
Did you get your binding issue resolved with the 9303? I am thinking about getting one for my 9303.
Thanks
Back to Top
JackChen View Drop Down
Platinum  (SG)
USERID: 83346
Newbie
Newbie
Avatar

Joined: 01/May/2009
Location: Singapore
Online Status: Offline
Posts: 11 		  Quote JackChen Quote  Post ReplyReply Direct Link To This Post Posted: 24/Jul/2010 at 11:57pm
hi all, I have been experiencing range problems recently with my Assan module. It wasn't there before, signal gets cut off at 10 m. It's been really bad, crashed planes tested with it.
Back to Top
adder View Drop Down
Platinum  (AU)
USERID: 280916
Newbie
Newbie


Joined: 01/Oct/2009
Location: Australia
Online Status: Offline
Posts: 18 		  Quote adder Quote  Post ReplyReply Direct Link To This Post Posted: 03/Sep/2010 at 3:12pm
Check your antenna is screwed up tight. I had same problem and it was loose.
Sound, sound the clarion, fill the fife,
Throughout the sensual world proclaim,
One crowded hour of glorious life
Is worth an age without a name.
(Thomas Mordaunt 1730-1809)
Back to Top
 Post Reply Post Reply Page  <12

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.54
Copyright ©2001-2008 Web Wiz

This page was generated in 0.266 seconds.