HobbyKing Forums
Forum Home Forum Home > Product Specific > Transmitters and Receivers
  New Posts New Posts RSS Feed: How-to: Using your transmitter for simulator use
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

How-to: Using your transmitter for simulator use
 Post Reply Post Reply Page  <1 23456 7>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
bedbug View Drop Down
Platinum  (CV)
USERID: 617174
Bargain Addict!
Bargain Addict!


Joined: 06/Sep/2010
Online Status: Offline
Posts: 61 		  Quote bedbug Quote  Post ReplyReply Direct Link To This Post Posted: 11/Nov/2010 at 3:19pm
I can't see what the problem is. A set of suitable cables to suit almost all transmitters is available on Ebay for around $9.00 for the lot (about 6 of them) and by using them I can run FMS, Clearview and any software which doesn't need a special dongle. But with the needed dongle I've never had any trouble running all my non transmitter type controllers and my Spektrum, Eurgle, Exceed and other transmitters from 30mhz to 2.4ghz. At the moment I'm using an 8 channel AST cheapie with every flight sim available
 
I'm into flight sims becaue I've been confined to bed for 7 years. I've never had to use any special software. The only one I have to change the transmitter for is RealFlight where I have to use the purpose made controller. I was lost when I first started but after much mucking about I managed to get a transmitter to work except for Realflight. I'm afraid I never wrote everything I did to get it to work but I just tried everything I could think of until it just worked. Those cables are a great deal, they fit just about all transmitters but usually the 3 connector 2.5mm stereo plug (the same as the small headphone plug) works well. But hey if you get results who cares how you get them.
Back to Top
flugzeug View Drop Down
Platinum  (BA)
USERID: 302794
HobbyKing aficionado
HobbyKing aficionado
Avatar

Joined: 20/Feb/2010
Online Status: Offline
Posts: 381 		  Quote flugzeug Quote  Post ReplyReply Direct Link To This Post Posted: 11/Nov/2010 at 3:28pm
Originally posted by Oimmuk

Tried this with the HK 6 ch 2.4 g system but it wont see the controller plugged into the usb port.../sigh.
 
Any have any luck with this?

I got it to work, will upload all drivers and stuff i used tonight ;)


Edited by flugzeug - 30/Nov/2010 at 5:41pm
rcmodelreviews*com
Back to Top
nguyentuanphu View Drop Down
Gold  (AU)
USERID: 653862
Newbie
Newbie


Joined: 29/Oct/2010
Online Status: Offline
Posts: 1 		  Quote nguyentuanphu Quote  Post ReplyReply Direct Link To This Post Posted: 30/Nov/2010 at 5:15pm
what the hell, i got  problems.
first is the windows received the driver => ok
but when i open the FMS then, configure them, it is just  like nothing
then after plugging in the radio in for few minutes, i unpluged, the radio just runs for few seconds then turn off with the a very fast beep.
i dont know why every time i run the radio it always comes with the beep
can you guys please help me to set up those things, this is my email or chat with me, nguyen.tuanphu@yahoo.com
thank you
Back to Top
ronepaulsen View Drop Down
Platinum  (ZA)
USERID: 564460
Newbie
Newbie


Joined: 19/Jul/2010
Online Status: Offline
Posts: 17 		  Quote ronepaulsen Quote  Post ReplyReply Direct Link To This Post Posted: 17/Dec/2010 at 3:43am
Has anyone managed to get the Turnigy 9x working on Phoenix? have a cheap transmitter that works without a problem - but cannot get the turnigy to work - I am using the orginal Phoenix earphone jack to USB cable
Back to Top
Rotormaster View Drop Down
Platinum  (AU)
USERID: 686866
HobbyKing aficionado
HobbyKing aficionado
Avatar

Joined: 18/Nov/2010
Online Status: Offline
Posts: 161 		  Quote Rotormaster Quote  Post ReplyReply Direct Link To This Post Posted: 29/Dec/2010 at 1:18pm
Does anybody know whether this method will work on a mac computer? I need to know so that I can know if I need to buy another transmitter or a "mock" USB sim transmitter. 

Any help would be great.
Back to Top
Christo View Drop Down
Platinum  (ZA)
USERID: 709460
Newbie
Newbie


Joined: 03/Jan/2011
Online Status: Offline
Posts: 1 		  Quote Christo Quote  Post ReplyReply Direct Link To This Post Posted: 03/Jan/2011 at 8:31pm
Hi,
I have a hobby king, HK-7Xv2 2.4GHz, 7 channel transmitter. I followed the SmartPropoPlus instructions for FMS.
My Setup:
The TX is set to PPM mode (RF light is off).
A mono audio jack is connected to the mic input of the PC.
FMS is installed on win7 with SmartPropoPlus.
FMS win7 d3drm.dll issues have been fixed.
SmartPropoPlus is set up for PPM(Generic).
(No filters applied in Smartpropo).

My problem is the following:
SmartPropoPlus receives the signal, but the channels interfere with each other. (Even after calibrating). When I move one stick on the transmitter, all the channels on FMS move (each with different amounts). This is not random movement, but with respect to how much I move the stick. This is the case for all the channels. It seems that SmartPropoPlus cannot decode the PPM signal properly. I have tried the other PPM and PCM settings on SmartPropoPlus, but with no success.

Has anyone encountered a similar problem? Has anyone got the HK-7Xv2 to work with smartpropoplus?
Back to Top
randonJ View Drop Down
Platinum  (AU)
USERID: 484852
Bargain Addict!
Bargain Addict!


Joined: 03/Jul/2010
Online Status: Offline
Posts: 20 		  Quote randonJ Quote  Post ReplyReply Direct Link To This Post Posted: 13/Jan/2011 at 8:24am
hi christo, i had that problem to.
what you have to do is turn off your transmitter and turn it back on holding down the two buttons on the left to enter model select mode. select a model your not using and then set the model type to either H1 or AV depending on what you are flying in the sim (H1 for heli). reset the transmitter to ppm mode and now the outputs should be seperated. you will also need to goto ppjoy and mess around with the chanel configurations.
i found HeliSimRc good to use with this because you can map the controlls in the sim. I still havent tried with FMS, think i could only get three chanels to work.
If you want some screen shots of my setup, just ask.
Back to Top
bogdand1 View Drop Down
Platinum  (RO)
USERID: 684190
Newbie
Newbie


Joined: 12/Nov/2010
Online Status: Offline
Posts: 14 		  Quote bogdand1 Quote  Post ReplyReply Direct Link To This Post Posted: 18/Jan/2011 at 11:31pm
I can't start Realflight G4 with HK T6A. I'm using T6sim 1.0 and PPjoy 0.83 and i'm geting "No authorized InterLink found.  Make sure youre Interlink Elite is plugged in and try agan". Anyone knows if they are compatible?

Never mind, I set T6sim's process to high and now works great.


Edited by bogdand1 - 24/Jan/2011 at 8:46am
Back to Top
klaw81 View Drop Down
Platinum  (AU)
USERID: 605444
Hobbyking Addict
Hobbyking Addict


Joined: 21/Sep/2010
Location: Queensland
Online Status: Offline
Posts: 504 		  Quote klaw81 Quote  Post ReplyReply Direct Link To This Post Posted: 21/Jan/2011 at 10:07am
Originally posted by Rotormaster

Does anybody know whether this method will work on a mac computer?
 
Only if you dual boot into a Windows installation. I've seen it working perfectly like that.
Back to Top
marmot View Drop Down
Platinum  (CZ)
USERID: 709524
Newbie
Newbie
Avatar

Joined: 07/Dec/2010
Location: Czech Republic
Online Status: Offline
Posts: 4 		  Quote marmot Quote  Post ReplyReply Direct Link To This Post Posted: 26/Jan/2011 at 9:38am
I am facing the the same problem. I can only get 3 channels too. The ailerons do not work. Have you found any solution in the meantime ?
Thanks.
Back to Top
 Post Reply Post Reply Page  <1 23456 7>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.54
Copyright ©2001-2008 Web Wiz

This page was generated in 0.234 seconds.